Home Our Difference Innovative Solution Sign Designs Self Assembly About Us Contact Us Legislation Links


Download our order form here (684 KB)


Fitting Instructions
(455 KB)

Legislation

Disability Standards for Accessible Public Transport 2002

as amended 
made under subsection 31 (1) of the 

Disability Discrimination Act 1992

This compilation was prepared on 11 May 2005
taking into account amendments up to Disability Standards for Public Transport
Amendment 2004 (No.2)

17.6 Raised Lettering or symbols or use of Braille

(1) If a sign incorporates raised lettering or symbols, they must be at least 0.8 mm above the surface of the sign.
(2) If an operator or provider supplements a notice with Braille characters, they must be placed to the left of the raised characters.

17.7 Taxi Registration Numbers

Raised taxi registration numbers must be placed on the exterior of the passenger doors forward of the handles

BCA Requirements

Section D3.6 of the Building Code of Australia (BCA)

In every building required to be accessible, clear and legible Braille and tactile signage complying with Specification D3.6 and incorporating the international symbol of access or deafness or other symbol as appropriate, in accordance with AS 1428.1 must identify-

(a) each-
(I) sanitary facility; and
(ii) accessible space with a hearing augmentation system; and
(b) where an entrance of lift is not accessible, identify each accessible-
(I) entrance; and
(ii) lift or bank of lifts; and
the path of travel from the principal public entrance to these features and facilities where their location is not apparent to the building occupant.

Specification D3.6 Braille and tactile signs

1. Scope

This specification sets out the requirements for the design and installation of Braille and tactile signage

2. Braille and Tactile signage

2.1 Location of Braille and tactile signs
Signs including symbols, numbering and lettering must be designed and installed as follows:

1. Signs must be located not less than 1200mm and not higher than 1600mm above the floor or ground surface.
2. Signs with single lines of characters must have the line of tactile characters not less than 1250mm and not higher than 1350mm above the floor or ground surface.
3. Signs identifying rooms containing features or facilities listed must be located;
(a) On the wall on the latch side of the door with the leading edge of the sign located between 50mm and 300mm from the architrave; and
(b) In the event of insufficient latch side dimension, a sign may be placed on the non-latch side of the door; and
Where (a) or (b) is not possible, the sign may be placed on the door itself.
4. Signs identifying paths of travel must be placed so they are located directly ahead in the direction of travel. Where one wall continues in the direction of travel and the other forms a corner, the sign must be placed on the continuing wall.

2.2 Location of Braille and tactile signs

The following applies to Braille and tactile sign orientation:
(a) Tactile characters must be raised or embossed to a height of not less than 1mm and not more than 1.5mm.
(b) Characters must have a height of not less than 17.5mm for each metre of viewing distance.
Upper case tactile characters must have a height of not less than 15mm and not more than 55mm.
(d) Lower case tactile characters must have a height of 50% of the related upper case characters.
(e) Tactile characters, symbols, and the link, must have rounded edges.
(f) The entire sign, including any frame, must have all edges rounded.
(g) The surface of the sign must be continuous for hygiene purposes.
(h) Signs must be constructed so as to resist the removal of letters and Braille dots by picking or adhesive failure.
(I) The background, negative space or fill of signs must be matt or low sheen finish.
(j) The characters, symbols, logos and other features of the signs must be matt or low sheen finish.
(k) The minimum letter spacing of tactile characters on signs must be 2mm.
(l) The minimum word spacing of tactile characters on signs must be 10mm.
(m) Fonts with letters of constant stroke thickness must be used.
(n) The thickness of letter strokes must be not less than 2mm and not more than 7mm.
(o) Tactile text must be left justified, except that single words may be centre justified.

2.3 Luminance-contrast

The following applies to luminance-contrast as defined in AS 1428.1:
(a) The background, negative space or fill of a sign or border must have a minimum luminance-contrast with the surface on which it is mounted of 30%.
(b) A border must be provided for luminance-contrast with the sign's background and shall have a minimum width of 5mm.
Tactile characters, icons and symbols must have a minimum 30% luminance-contrast with their background or fill within the sign.
(d) Luminance-contrasts must be met under the lighting conditions in which the sign is to be located.

2.4 Lighting

Braille and tactile signs must be illuminated to ensure luminance-contrast requirements are met at all times during which the sign is required to be read.

2.5 Braille

The following applies to Braille:
(a) Braille must be grade 1 Braille (uncontracted) in accordance with the criteria set out by the Australian Braille Authority.
(b) Braille must be raised and domed.
Braille must be located 8mm below the bottom line of text (not including descenders) 
(d) Braille must be left justified.
(e) Where an arrow is used in the tactile sign, a small arrow must be provided for Braille readers.
(f) On signs with multiple lines of text and characters, a semi-circular Braille locator at the left margin must be horizontally aligned with the first line of Braille text.
(Source: Building Codes of Australia 2005- Volume One)

 

Site by V6 Internet Services